We pride ourselves on providing our customers with a wide range of stains for all types of surfaces, whether it be for interior or for exterior applications. If you're using more than one gallon of the same color, mix them together then apply to your surface for an even distribution of color. It is highly recommended to test a small inconspicuous area first. Custom colors available.
Simple Stain
Classic Simple Stain is an easy-to-use water-based stain that enhances the aesthetic of many different types of surfaces. Multiple colors can be used to create unique and beautiful results. This advanced formula allows color to reach its full potential almost immediately upon application. Color may be built up without the worry of damaging the concrete like acid stain does. Classic Simple Stain is UV stable and has Zero VOC. After applying the first coat, you only have to wait 10 - 20 minutes to apply the second coat at 75ºF. All colors may be used on interior and exterior surfaces in a wide range of environments. Apply Classic Coatings Systems Sealer over the stain to protect the color and make it more vibrant. It is highly recommended to test a sample area first. If you are using more than one gallon of the same color, mix them together in a 5-gallon pail, then apply the stain to your surface for a uniform distribution of color. New concrete must cure for 28 days before the stain can be applied.
FX NANO SEMI-TRANSPARENT DECORATIVE STAIN
Classic FX Nano Semi-Transparent Water Base Decorative Stain is a great alternative to acid staining. Since no chemical reaction is taking place, there is no extended waiting time for color penetration and no need to neutralize. The penetrative reaction of the stain preserves and protects against wear and exposure when sealed. FX Nano is simple to use and requires low maintenance. It is UV stable and has zero VOC. This advanced formula allows color to reach its full potential almost immediately upon application. Color may be built up without the worry of damaging the concrete like an acid stain does. Numerous coats can be applied instantly so there is no need to apply them for an extended period of time. All colors may be used on interior and exterior surfaces in a wide range of environments. Multiple colors can be used to achieve a custom look. Apply a Classic Coatings Systems Sealer over the stain to make it pop and give it a more vibrant finish. One gallon covers approximately 350-500 sq. ft. depending on application technique and surface. It is highly recommended to test a sample area first. Surface is slippery when wet. New concrete must cure for 28 days before the stain can be applied.
FX2 ARMOR NANO INDUSTRIAL GRADE STAIN
FX2 is a single-component acrylic polymer blend penetrating water-based stain. It provides excellent penetration, UV stability, and it won't crack, peel, or yellow. It can be applied over cementitious toppings, concrete, masonry, pavers, driveways, and polished concrete surfaces up to 400. FX2 is environmentally safe with no need to neutralize and no fumes or cleanup of hazardous chemicals with VOC and is semi-transparent. FX2 colors reach their full potential within minutes of application and can be built up without the worry of damaging the concrete as an acid stain does. Note that a Classic Sealer must be applied and will make the color more vibrant. For both indoor and outdoor use. We HIGHLY recommend testing a sample area first since results can vary for different surfaces. New concrete must cure for 28 days before applied. Available in 1 gal. jugs, 5 gal. pails and 55 gal. drums
WATER BASE NANO-HYBRID DECORATIVE STAIN
Classic Water-based Nano-Hybrid Stain is a water-based acrylic polymer emulsion, formulated for easy application and beautification of concrete and masonry surfaces. The oxides become a permanent part of the substrate. The resulting effect creates a more opaque finish. For example, the formation of iron oxide will produce a reddish-brown mottled rust color. Considerable variations in color and tone normally result from the use of Classic Stain. Many special color effects may be achieved using different application techniques. Classic's color stain provides a natural art deco look over old and new surfaces, interior and exterior. Classic Custom Waterbase Stain is an environmentally friendly alternative to acid stains. New concrete must cure for 28 days before application. Available in 1 gal. jugs, 5 gal. pails and 55 gal. drums.
NANO-INFUSED DECORATIVE CONCRETE STAIN
Classic Nano-Infused Concrete Stain is a specially formulated non-reactive semi-transparent stain that will penetrate and color most porous surfaces. It can be mixed with water, acetone, or denatured alcohol. It is a ZERO VOC product with no odor and cutting-edge technology to bring you the smallest particle size available in a concrete stain to allow the greatest penetration. It is ideal for interior or exterior use as it is UV-protected and will not fade in the sun. It is packaged as a liquid concentrate. Mottled looks similar to acid or dye stain applications can be accomplished with application techniques. Nano-Infuse can be sealed with Classic water base sealers or solvent sealers within two hours of drying. Application is easiest with a pump sprayer with a conical tip. Tip size of .05 to .15 gpm at 30-40 psi is recommended to reach coverage rates of 400-600 sqft. per gallon. New concrete must cure for 28 days before stain is applied. Available in 1 quart concentrate. See Tech Data Sheet for mixing instructions.
TRADITIONAL DECORATIVE ACID STAIN
Classic Traditional Decorative Acid Stain is a single-component coloring solution of acidic metallic ion particles. When placed on a cementitious surface, it allows the metallic ions and the particles in the cement (free alkali) to form oxides. These oxides become a permanent part of the substrate and will not crack or peel. The resulting effect creates a colored, variegated, and sometimes marbleized effect. Considerable variations in color and tone normally result from the use of Classic Acid Stain. Many special color effects may be achieved using different application techniques. Acid stains may give you unique looks and visual characteristics that cannot be achieved by using conventional polymer or pigment-type stains. This is due to the acid reacting individually with each substrate depending on the cement’s content, age, porosity, and the manner in which hydration takes place. These variables are the reason for its inherent beauty. New concrete must cure for 28 days before stain is applied. Available in 1 gal. jugs, 5 gal. pails and 55 gal. drums.
SURE-BOND DECORATIVE CONCRETE POLISH DYE
Classic Sure-Bond Concrete Polish Dye is currently being supplied in 22 standard colors. Custom colors are available. Sure-Bond Concrete Polish Dye colors can be combined to create an unlimited number of color variations. When applied properly, Sure-Bond Concrete Polish Dye gives a wonderful and bright color to polished concrete floors. Anytime that Sure-Bond Concrete Polish Dye is used in a process other than polished concrete "Classic Guard II" is required. It brightens the color and retards color loss over time. This liquid hardener is to be used to lock in the color on the polished concrete to intensify the colors and minimize UV fade. Classic Sure-Bond Concrete Polish Dye is formulated, using extremely fine molecules of color, and when mixed with acetone or water at “1 gallon per color pack either acetone or water, acetone is recommended”, penetrates indoor polished concrete floors to create beautiful color finishes that will last for years. Sure- Bond Concrete Polish Dye was created for use with any polished concrete floor system but can be used as a base color or touch-up for acid-stained concrete or as a coloring agent itself. For Interior Use Only. New concrete must cure for 28 days before dye is applied. Available in 1 quart concentrate. See Tech Data Sheet for mixing instructions.
ELASTO COAT DECK COATING
Classic Elasto Coat Deck Coating line is a single component with an elastomeric product built-in. It is available in Zero VOC waterborne opaque solid colors. Elasto Coat is formulated for use on pool decks, concrete surfaces, wood fences, balconies, decks, masonries, pavers, stones, block walls, and bricks. It may be used for interior, exterior, flat, and vertical surface applications in a wide range of climates. It has excellent UV stability, repels water, and will not yellow. Elasto Coat is designed as a long-lasting deck coating that would be flexible with a built-in anti-skid and yet very durable for high-traffic areas. Elasto Coat is available in a smooth or clear finish. It is ideal for applications on concrete restoration projects. Elasto Coat is a low-maintenance product provided that the surface is properly prepared. Elasto Coat is very easy to apply by using a paint roller, is environmentally safe, and easy to clean up. When using more than one gallon on the same job it is HIGHLY recommended to mix together in a 5 gal container at low speed. Ready to use has a built-in texture with a medium sheen finish. Custom colors are available. New concrete must cure for 28 days. Available in 1 gal. jugs, 5 gal. pails and 55 gal. drums.